Ultrasaten is ultra stain-resistant and ecological, super-covering, super-washable, scratch-resistant and highly resistant to abrasion. It allows perfect cleaning with a simple sponge wipe without damaging or discoloring any finish. It resists every stain: splashes of drinks, coffee, sauces, fruit juices, mud but also children’s drawings on the walls. Haccp certified, it is ideal for environments where continuous and long-term cleaning is essential such as stairs, corridors, kitchen, children’s room. Available in over 3000 colors and 3 gloss variants: satin and glossy.

Surface Preparation
Clean the surface, removing any loose material. For crumbly or very absorbent substrates, apply the recommended acrylic fixative CRILUX or NEOFIX by OIKOS. Wait at least 6 hours before painting. In order to increase the coverage of the cycle use as primer IL PIGMENTATO by OIKOS. In the event that the decoration requires a perfectly smooth finish, screed over the surface first with STUCCO IN PASTA PER RASATURA by OIKOS.

Application Method
Apply two coats of ULTRASATEN diluted 20-25% with drinkable water, leaving 4-6 hours between each coat. ULTRASATEN can be applied by roller, brush or spray gun. It is a self-expanding product that does not leave signs of roller or brush strokes. By adding one litre of BIAMAX 03 base TR to four litres of Ultrasaten (Gloss, Satin or Matt), it is possible to obtain a mix with which very particular decorative effects can be created:
Sabbiato Effect: on a smooth surface apply by brush, in an irregular maner, one coat of the ULTRASATEN/Biamax mix, diluted 20-25% with water. After a few minutes, pass back over the surface with the brush free of product, in order to highlight and bring out further the effect. If the coverage is not sufficient, after 4-6 hours a second coat can be applied. The yield varies according to the quantity of product applied. Yield 9-10 mq/lt. For this finish it is also possible to obtain the Stellato effect by adding two pots of the additive Decorglitter for every litre of the mix that is vreated.

Le Trame Effect: on a smooth surface apply one coat of Fondo Murales. After drying, using a brush apply one coat of the ULTRASATEN/ Biamax mix diluted 15% with water, taking care to pass over the product for the last time in a horizontal direction, immediately work the surface by dragging the Tool for Corduroy effect in the same direction. In order to eliminate eventual imperfections caused by accumulations of product, before the product is dry, pass back over the surface with the Spatola Dentata. Once dry, repeat the operation, always applying the product in a horizontal sense but working over the surface with the Tool for Corduroy effect in a vertical sense and using the Spatola dentata to remove eventual imperfections. It is essential to regularly clean excess product from the Tool for Corduroy effect in order to avoid the formation of lumps. Yield 4-5 mq/lt.
For this finish it is possible to obtain the Stellato effect by adding one pot of the additive Decorglitter to every litre of the mix generated. These effects can also be used as the base for the application of other Oikos decorative products thus further enlarging the range of decorative finishes that can be achieved. In these instances it is best to mix Biamax into the MATT version of ULTRASATEN.

Safety Information
The product is free of heavy metals such as lead or chrome. It does not contain toxic solvents, aromatics or chlorides. There is no risk of any dangerous polymerisation. The product is considered to be a non dangerous substance if used in the technically correct manner. Normal cautionary measures for the handling of water based paints are advised. No special arrangements are required for the storage, movement and transportation of the product; the containers, residue, eventual spilt material should be cleaned up using absorbent inert material such as sand, soil etc. and then disposed of in accordance with the regional and national regulations in force at that time. Transportation must be carried out in accordance with international agreements.

Specifications
Thoroughly clean the surface, removing any loose material. For crumbly or very absrobent substrates, apply a sealer based on acrylic resins such as CRILUX or NEOFIX by OIKOS. In order to increase  the coverage of the cycle use as a primer IL PIGMENTATO by OIKOS. Wait at least 6 hours before painting. Apply then two coats of an ecological enamel for walls such as ULTRASATEN by OIKOS, cleanable, extra washable (class 1), in class A+ under emissions classification, compiant with standard UNI 11021:2002 for use in environments where there are food stuffs present. All must be carried out in accordance with the norms of application.